AutoCAD 2D & Isometric | AutoCAD Civil & Architectural
- Description
- Curriculum
- FAQ
- Reviews
Learn skill to earn the skill.
AutoCAD is a prime product of Autodesk. AutoCAD is the most prominent product used globally for 2D work. AutoCAD applications can be found in different engineering disciplines like Civil, Mechanical, Architecture, Electrical, Electronics, etc. But this AutoCAD course is not designed from AutoCAD Mechanical, Electrical, or Electronics perspective. This AutoCAD course is limited to AutoCAD Civil, and Architectural disciplines only.
This is an AutoCAD 2D course and it doesn’t cover AutoCAD 3D. So we’ll work in the Drafting & Annotation workspace which is a 2D workspace in AutoCAD. This AutoCAD course will be started with ‘Introduction of AutoCAD Interface’. We will try to cover each & every 2D command which later on is going to be used in the project. Once we get the expertise in using AutoCAD 2D commands then we will start working on the project & will create a complete 3 BHK ground+1 story 2D House Plan, along with Front Elevation, Side Elevation & Sectional Elevation in AutoCAD. We’ll create a Location Plan, Site Plan, & Column Layout Plan as well. Other than these definitely we’ll have more work on the Floor Plan & for every new task separate video tutorial is made. We’ll work according to the submission drawing & print the submission drawing as well. Also, we will see how to use external references & how to digitize any plan in AutoCAD.
Before starting the project we’ll learn about different design considerations which are necessary to learn before designing any residential building. This is not about AutoCAD so even if you create a drawing by hand on paper or if you are supervising the construction work you must have some knowledge about these design considerations. Don’t miss this lecture! This is a short but very important lecture.
This course is not just limited to AutoCAD 2D. We’ll also learn about Isometric Drafting & Orthographic Projection in AutoCAD. A separate section is made about Isometric Drafting & Orthographic Projection in AutoCAD.
This AutoCAD 2D course has a total of 95 video tutorials with a total length of more than 18 hours. This AutoCAD 2D course is designed by assuming that you are using AutoCAD for the very first time & don’t have any previous knowledge or never worked before in AutoCAD.
This course is designed in AutoCAD 2017 version but it can be easily learned in almost any older or latest version of AutoCAD.
Some files are attached as resources you can download and use.
This AutoCAD course is divided into the following sections:
-
AutoCAD presets
-
Draw Toolbar
-
Modify Toolbar
-
Status Bar Keys
-
Text command in AutoCAD
-
Table command in AutoCAD
-
Dimensioning the Drawing File
-
Multi Leader Command
-
Block & Group
-
Object Properties
-
Layer Properties
-
AutoCAD Utilities
-
Isometric & Orthographic projection
-
Residential Building Design
-
Location Plan & Site Plan
-
Working on Floor Plan
-
Working on 2D Elevation
-
Column Layout Plan
-
Compass & Title Block
-
Printing AutoCAD Drawing
-
External References & Digitization of Plan
There are plenty of topics under these sections in separate videos. I will suggest must go through all the videos. Don’t skip if you properly want to get the outcome of this course.
Note: Please go through all the topic titles before enrolling in this course. Also, I tried to explain the course content in the description as well & have made enough videos available for free preview so that you can decide if you should get this course or not. I recommend joining the course only if you think this course matches your expectations.
So, If You are Fully Satisfied Hit the ‘Enroll Now’ Button & Enjoy the AutoCAD Training. Happy Learning!
-
1
Introduction to AutoCAD InterfaceIn this video, we will do an Introduction to the AutoCAD Interface.
-
2
Customizing the AutoCAD Interface
In this video, we will learn to customize AutoCAD Interface.
-
3
AutoCAD Classic Workspace
In this video, we will know about AutoCAD Classic Workspace.
-
4
Navigation Tools in AutoCAD
In this video, we will learn about Navigation commands like Pan, Zoom & Orbit in AutoCAD.
-
5
Customizing the Cursor
In AutoCAD, a cursor has 2 components crosshair & pick box. In this video, we will learn how to customize crosshair & pick box.
-
6
Saving the AutoCAD File
In this video, we will learn to save drawing files in AutoCAD.
-
7
Unit & Limit Settings
In this video, we will learn to set units & limits in AutoCAD.
-
8
Line Command
In this video, we will learn about the Line command.
-
9
Polyline Command
In this video, we will learn about the Polyline command.
-
10
Circle Command
In this video, we will learn about the Circle command.
-
11
Arc Command
In this video, we will learn about the Arc command.
-
12
Rectangle Command
In this video, we will learn about the Rectangle command.
-
13
Polygon Command
In this video, we will learn about the Polygon command.
-
14
Ellipse Command
In this video, we will learn about the Ellipse command.
-
15
Spline Command
In this video, we will learn about the Spline command.
-
16
Construction Line & Ray Commands
In this video, we will learn about the Construction Line & Ray commands.
-
17
Point Command
In this video, we will learn about the Point command.
-
18
Divide & Measure Commands
In this video, we will learn about the Divide & Measure commands.
-
19
Hatch Command
In this video, we will learn about the Hatch command.
-
20
Gradient Command
In this video, we will learn about the Gradient command.
-
21
Boundary & Region Commands
In this video, we will learn about the Boundary & Region commands.
-
22
Copy & Move Commands
In this video, we will learn about the Copy & Move commands.
-
23
Trim Command
In this video, we will learn about the Trim command.
-
24
Extend Command
In this video, we will learn about the Extend command.
-
25
Erase Command
In this video, we will learn about the Erase command.
-
26
Rotate Command
In this video, we will learn about the Rotate command.
-
27
Mirror Command
In this video, we will learn about the Mirror command.
-
28
Fillet Command
In this video, we will learn about the Fillet command.
-
29
Chamfer Command
In this video, we will learn about the Chamfer command.
-
30
Explode Command
In this video, we will learn about the Explode command.
-
31
Stretch Command
In this video, we will learn about the Stretch command.
-
32
Scale Command
In this video, we will learn about the Scale command.
-
33
Offset Command
In this video, we will learn about the Offset command.
-
34
Lengthen Command
In this video, we will learn about the Lengthen command.
-
35
Align Command
In this video, we will learn about the Align command.
-
36
Break Command
In this video, we will learn about the Break command.
-
37
Join Command
In this video, we will learn about the Join command.
-
38
Overkill Command
In this video, we will learn about the Overkill command.
-
39
Rectangular Array Command
In this video, we will learn about the Rectangular Array command.
-
40
Polar Array Command
In this video, we will learn about the Polar Array command.
-
41
Path Array Command
In this video, we will learn about the Path Array command.
-
42
Selection Options in AutoCAD
In this video, we will learn about the different Object Selection options in AutoCAD.
-
43
Grid & Snap Mode
In this video, we will learn about Grid Mode & Snap Mode in AutoCAD.
-
44
Dynamic Input
In this video, we'll learn about the Dynamic Input option.
-
45
Ortho Mode & Polar Tracking
In this video, we will learn about Ortho Mode & Polar Tracking.
-
46
Object Snap
In this video, we will learn about the Object Snap option.
-
47
Object Snap Tracking
In this video, we will learn about Object Snap Tracking.
-
48
Other Status Bar Keys
In this video, we will learn about some more Status Bar Toggle keys like selection cycling, dynamic UCS, quick properties, isolating objects, etc.
-
55
Dimension Options in AutoCAD
In this video, we will learn about multiple Dimension Options.
-
56
Dimension Command
In this video, we will learn how to use different dimension options with the Dimension command in AutoCAD.
-
57
Quick Dimension
In this video, we will learn about the Quick Dimension option in AutoCAD.
-
58
Continue & Baseline Dimension Options
In this video, we will learn about Continue Dimension and Baseline Dimension commands in AutoCAD.
-
59
Customizing the Dimension Style
In this video, we will learn how to Customize the Dimension Style.
-
60
Override Dimension Style
In this video, we will learn how to Override Dimension Style in AutoCAD.
-
61
Tolerance Options in AutoCAD
In this video, we'll learn about Tolerance Options in AutoCAD.
-
64
Creating Block in AutoCAD
Block command is used to make multiple objects act as a single object. In this video, we will learn about the Block command in AutoCAD.
-
65
Inserting & Editing Blocks
In this video, we'll learn how to Insert & Edit the Blocks.
-
66
Grouping the Objects
Group command is used to create a set of different objects or blocks. In this video, we will learn about the Group command in AutoCAD.
-
72
Isometric Drafting-01
In this video, we will learn about Isometric Drafting in AutoCAD.
-
73
Isometric Drafting-02
In this video, we will continue the Isometric Drafting in AutoCAD.
-
74
Orthographic Projection
In this video, we will learn about Orthographic Projection. We'll create orthographic views of an Isometric Object.
